[ITEM IS SOLD]
Warmoth conversion neck, purchased new in 2021. Excellent / mint condition. $300 OBO PP'd and shipped. The neck is now substantially better than how Warmoth ships them -- fret ends were rounded, fretboard edges slightly rolled, frets polished to mirror finish, and neck was...
Like said above, if it's a new Warmoth neck, DO NOT try to level the entire fretboard; there's no need and you may just mess it up. Instead, get a fret rocker and go fret by fret looking for high spots, then just level the high spots. Use 600 grit. YES, 600 grit. There's absolutely no need to...
I'm building my first tele, and received the body after a mere 4 week wait. Thanks Warmoth! Incredibly, they sent me a one-piece body (swamp ash), which I didn't even request. Wow.
The concept here is a lightly-relic'd tele that looks vintage but with some modern features. So roasted flamed...
NOT SO! The instructions explain how you can destroy it. There are stories of guys turning the side-adjust and hearing the dreaded PING, meaning they just destroyed the truss rod assembly internally. There's an entire 1-page set of complicated instructions and cautions setting up the two...
+1. Not only do I have no use for the side-adjust feature, I completely despise and fear it tremendously. I just bought my first Warmoth side-adjust neck last year, and I've already completely forgotten how to adjust it properly without destroying it. This puts me at very high risk of...
Like I explained above, decking (tightening the springs until the trem sits against the body) a FR trem is objectively a BAD IDEA because it won't sit flat against the body and will probably damage the top too. It's *possible* yours might sit flush and won't damage the body, but very unlikely. ...
What is “one of the main reasons…”? You can get the body you described from lots of suppliers.
Like I explained on pg 2, you don’t want to deck a FR trem. That’s not really done since it doesn’t usually work. You need a trem stopper.
Tele into an EL84 amp (e.g. Vox, Dr Z, Magnatone) is a special kind of magic. Really. It just works better than into a Fender or Marshall, IMHO, for styles like country, blues, americana.
Like Stratamania said, if you're non-recessed but with a standard non-angled pocket, you'll try to lower the action by lowering the bridge... but then your bridge hits the body and the action is still too high. So the answer (like The Aaron's quote) is to angle the neck pocket. The big problem...
Correct. If you want dive only, non-recessed, then specify non-angled pocket. But may be a possibility of needing a very thin (like .25 degree) shim. Unlikely though. If you get an angled pocket, you could still make it work but you're guaranteed to require a thick 1 degree shim or thereabouts.
Carved top Soloists are super cool. Downsides: you can't do natural binding, it adds quite a bit of weight, and you don't have the nice arm cutaway on top. The showcase bodies I saw seemed to weigh ballpark 13 oz more than non-carved top bodies, but OTOH Soloists are generally very light...
You're not going to get what you want. Decking a FR (i.e. tightening the springs down) is not commonly done because of how the FR bridge will hit and ding up the body, unlike Strat-type trems (Fender, Gotoh 510) that can rest on the body with good contact. Even with a 1-degree shim, the trem...
This is a normal and completely predictable issue. If you DON'T want the trem to float, you should have asked for a non-angled pocket. But here's the deal -- even if you want it to float, the standard angled pocket raises it excessively. I just went through this on a non-Warmoth body, and added...
Just to follow up, this guitar came together wonderfully, including that ferrule arrangement. I might also add that I used a 1/2" forester bit (12.7mm) to drill the holes for the 14mm ferrules. I wasn't totally sure that would leave enough room for paint, and also I was a bit concerned I may...
Yes thank you, I should have been more careful with my wording. Musikraft doesn't level or polish the frets. They do round the fret ends (just barely) and roll the edges to my liking, though. Which saves 2 hrs effort by the owner if you're slow like me.
I wanted to copy the Charvel Govan heel too, so here's what I came up with. Body and neck were pre-drilled in the standard positions. I used a drill press to drill the ferrule holes, which was breeze. Got some smaller 12mm ferrules because most (14mm) would be too close to the one edge. For...
Indeed! I bought a pack of Fender screws and will need to cut one down. I hate doing that, but c'est la vie.
Another big "gotcha" there is to realize that not all neck screws have the same thread pitch! If you buy "off-brand" screws then swap screws of different pitches, you'll strip out the...
This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
By continuing to use this site, you are consenting to our use of cookies.